Overall dimensions and technical information are given for information purposes only and are subject to change without notice 22 Electric linear axes Catalogue GENERAL DATA Max. speed [m/s] 5 5 5 5 5 5 5 5 Max. acceleration [m/s²] 50 50 50 50 50 50 50 50 Repeatability [mm] ± 0.05 ± 0.05 ± 0.05 ± 0.05 ± 0.05 ± 0.05 ± 0.05 ± 0.05 Guide type Type ball recirculation Top & side guide size 15 15 15 15 25 25 30 30 Belt type Type 16-AT5 16-AT5 25-AT5 25-AT5 32-AT10 32-AT10 50-AT10 50-AT10 Pulley primitive diameter [mm] 35.03 35.03 38.21 38.21 50.95 50.95 63.9 63.9 Displacement per pulley revolution [mm] 110 110 120 120 200 200 200 200 Number of blocks n 1 2 1 2 1 2 1 2 DIMENSIONAL DATA L: Carriage length [mm] 100 160 110 180 180 260 260 360 L1: Head length [mm] 60 60 60 60 90 90 90 90 L2: Distance hole to carriage edge X [mm] 20 20 5 5 30 30 25 30 L3: Carriage hole centre distance X [mm] 60 60 50 50 60 50 70 60 L4: Carriage pin hole centre distance X+/-0.05 [mm] 60 120 100 170 - - - - W: Carriage width [mm] 43 43 58 58 75 75 118 118 W1: Head width [mm] 45 45 60 60 80 80 120 120 W2: Carriage hole centre distance Y [mm] 26 26 50 50 60 60 100 100 W3: Distance hole to carriage edge Y [mm] 8.5 8.5 4 4 7.5 7.5 9 9 H: Carriage height [mm] 62 62 65 65 100 100 100 100 H1: Head height [mm] 60 60 60 60 90 90 90 90 D: Pulley hole diameter [mm] Ø22 H7 Ø22 H7 Ø22 H7 Ø22 H7 Ø32 H7 Ø32 H7 Ø40 H7 Ø40 H7 D1: Fixing hole diameter on drive head [mm] M4x8 M4x8 M4x8 M4x8 M6x12 M6x12 M6x16 M6x16 D2: Carriage bore diameter [mm] M5x7 M5x7 M5x16.5 M5x16.5 M8x16 M8x16 M10x20 M10x20 D3: Carriage pin hole diameter [mm] Ø4 H7 Ø4 H7 Ø4 H7 Ø5 H7 - - - - L5: Head hole centre distance X [mm] 50 50 50 50 70 70 70 70 H2: Head hole centre distance Y [mm] 50 50 50 50 70 70 70 70 L6: Groove centre distance X [mm] - - 30 30 40 40 80 80 L7: Groove-edge distance X-axis [mm] 22.5 22.5 15 15 20 20 20 20 H3: Groove centre distance Y [mm] - - - - 30 30 30 30 S: Max. stroke [mm] 5500 5500 5500 5500 5500 5500 5500 5500 T: Total length [mm] L1+5+L+S+5+L1 L1+10+L+S+10+L1 Protection Option N/A N/A N/A N/A N/A N/A N/A N/A MASS DATA Zero stroke base axis [kg] 1.20 1.50 1.9 2.6 5.5 5.8 9.2 11.3 Mass for each 100 mm of stroke [kg] 0.30 0.30 0.4 0.4 0.8 0.8 1.1 11.1 Carriage [kg] 0.20 0.30 0.5 0.9 0.8 1.1 3.2 5.1 SECTION MOMENT OF INERTIA Section inertia extruded profile Lyy [cm4] 7.1 7.1 17.3 17.3 74.4 74.4 120 120 Section inertia extruded profile Lzz [cm4]. 13.8 13.8 47.6 47.6 151.2 151.2 492 492 MAXIMUM RECOMMENDED LOADS (*) Fx [N] 823 823 3077 3077 3969 3969 6608 6608 Fy [N] 1535 2011 2185 3220 4673 6122 5670 7934 Fz [N] 2944 4409 2297 3681 6653 9731 10000 18516 Mx [Nm] 9 10 17 20 42 47 58 66 My [Nm] 94 167 94 253 496 776 436 610 Mz [Nm] 79 125 79 154 412 597 272 577 MLBNSTD120-AX12 MLBNSTD120-AX11 MLBNSTD080-AX12 MLBNSTD080-AX11 MLBNSTD060-AX12 MLBNSTD060-AX11 MLBNSTD045-AX12 MLBNSTD045-AX11 STD SERIES (*) The maximum recommended loads are intended as the maximum value that can be applied individually and statically. In the case of combined load configurations, please contact the AutomationWare technical department.
RkJQdWJsaXNoZXIy NzYzOTY1