Overall dimensions and technical information are given for information purposes only and are subject to change without notice 72 Electric linear axes Catalogue GENERAL DATA Max. speed (**) [m/s] 0.4-0.8 0.4-0.8 0.5-1 0.5-1 0.7-1.3-2.5 0.7-1.3-2.5 Max. acceleration [m/s²] 50 50 50 50 50 50 Repeatability [mm] ± 0.01 ± 0.01 ± 0.01 ± 0.01 ± 0.01 ± 0.01 Guide type Type ball recirculation Guide size mm 12 12 15 15 20 20 Screw diameter mm 12 12 16 16 20 20 Screw pitch [mm/rev] 05-10 05-10 05-10-16 05-10-16 05-10-20 05-10-20 Number of blocks n 2 4 2 4 2 4 DIMENSIONAL DATA L: Carriage length [mm] 100 160 110 190 180 260 L1: Motorised head length [mm] 30 30 30 30 20 20 L2: Conducted head length [mm] 20 20 15 15 20 20 L3: Distance hole to carriage edge X [mm] 5 5 20 20 10 10 L4: Carriage hole centre distance X [mm] 90 50 35 50 80 60 L5: Carriage pin holes centre distance X+/-0.05 [mm] 88 148 - - - 220 L6: Distance pin hole to carriage edge X [mm] 6 6 - - - 20 W: Carriage width [mm] 88 88 118 118 158 158 W1: Motorised head width [mm] 90 90 120 120 160 160 W2: Conducted head width [mm] 90 90 120 120 160 160 W3: Carriage hole centre distance Y [mm] 80 80 110 110 70 70 W4: Distance hole to carriage edge Y [mm] 4 4 4 4 9 9 W5: Carriage pin hole centre distance Y +/- 0.05 [mm] 38 38 - - - - W6: Distance pin hole to carriage edge Y [mm] 25 25 - - - 79 H: Carriage height [mm] 50 50 68 68 100 100 H1: Motorized head height [mm] 45 45 66.5 66.5 95 95 H2: Conducted head height [mm] 45 45 66.5 66.5 95 95 L7: Shank length [mm] 16 16 16 16 25 25 L8: Footprint length [mm] 16.4 16.4 37 37 54 54 D: Shank size [mm] 8 8 10 10 12 12 H3: Screw centre height [mm] 23 23 36.5 36.5 48.5 48.5 D1: Fixing hole diameter on drive head [mm] M4x8 M4x8 M4x8 M4x8 M6x12 M6x12 D2: Carriage bore diameter [mm] M4x8 M4x8 M5x10 M5x10 M8x16 M8x16 D3: Carriage pin hole diameter [mm] Ø2.5 H7 Ø2.5 H7 - - - Ø6 H7 L9: Head hole centre distance X [mm] 30 30 50 50 70 70 H4: Head hole centre distance Y [mm] 30 30 50 50 70 70 L10: Groove centre distance X [mm] 60 60 80 80 40 40 L11: Groove-edge distance X-axis [mm] 15 15 20 20 20 20 H5: Groove centre distance Y [mm] - - - - 50 50 S: Max. stroke [mm] 400 400 800 800 1000 1000 T: Total length [mm] L8+L1+5+L+5+S+L2 Protection Option Stainless steel sheet MASS DATA Base with zero stroke [kg] 1.6 2.2 3.3 4.5 8.3 11.1 Mass per 100 mm of stroke [kg] 0.7 0.7 1.2 1.2 1.6 1.6 Complete carriage [kg] 0.5 0.8 1.1 1.6 2.9 4.4 SECTION MOMENTS OF INERTIA Moment of inertia Lyy [cm4] 9.6 9.6 27.2 27.2 176 176 Moment of inertia Lzz [cm4]. 9.1 9.1 291 291 1096 1096 MAXIMUM RECOMMENDED LOADS (*) Fx (***) [N] 560-400 560-400 600-830 600-830 1010-1270-1600 1010-1270-1600 Fy [N] 3064 7665 6277 9986 5199 8169 Fz [N] 5779 11922 12337 23333 9384 16636 Mx [Nm] 33 37 99 129 206 268 My [Nm] 23 283 154 635 475 923 Mz [Nm] 23 171 129 385 288 559 MLSTPRO160-AX22 MLSTPRO160-AX24 MLSTPRO120-AX24 MLSTPRO120-AX22 MLSTPRO090-AX24 MLSTPRO090-AX22 PRO SERIES (*) The maximum recommended loads are intended as the maximum value that can be applied individually and statically. In the case of combined load configurations, please contact the AutomationWare technical department. (**) Data refer to a stroke of 400 mm. Different strokes result in different speed limits, contact AutomationWare's technical department for a detailed study. (***) Load value refers to a useful life of 2000 km.
RkJQdWJsaXNoZXIy NzYzOTY1