Optyma-S e Optyma-Sc

Overalldimensionsand technical informationareprovidedsolely for informativepurposesandmaybemodifiedwithoutnotice 8 Input/Output Module Air distribution Solenoid valves manifold 8 Series 2200 "OPTYMA-S" - Accessories 1 4 3 1 4 3 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 PIN 11 PIN 12 PIN 13 PIN 14 PIN 15 PIN 16 PIN 17 PIN 18 PIN 19 PIN 20 PIN 21 PIN 22 PIN 23 PIN 24 PIN 25 PIN 26 PIN 27 PIN 28 PIN 29 PIN 30 PIN 31 PIN 32 PIN 33 PIN 34 PIN 35 PIN 36 PIN 37 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 PIN 11 PIN 12 PIN 13 PIN 14 PIN 15 PIN 16 PIN 17 PIN 18 PIN 19 PIN 20 PIN 21 PIN 22 PIN 23 PIN 24 PIN 25 The I/O module changes it is operation depending on the way the manifold is controlled. There are two possiblemodes: A) Control viamulti-pole connection B) Control via fieldbus Connection modes: M8 connector used as Input: A) Control via multi-pole : Attention: Since every cable has a degree of resistance, there will always be a voltage drop depending on the cable’s length, sectional area and the current. Attention: Voltage applied to each connector is passed to multi-pole connector pin. Output voltage will the same as is applied at the multi-pole connector pin. The maximum output current depends upon the power unit used, but we recommend nomore than 250mA. M8 connector used as Output: Attention : Optyma 32- S solenoid valve manifolds permit up to 22 electrical signals that are not used by manifolds to be made available: these signals can bemanaged by another manifold and / or by I/Omodules. The I/Omodule will manage these unused signals. Connections that are not managing useful signals will remain unconnected. PIN DESCRIPTION 1 THROUGH LINE SUB-D TYPE 37 POLE MALE CONNECTOR 1 - 32 = SIGNALS 33 - 35 = GND 36 - 37 = THROUGH LINE 1 - 22 = SIGNALS 23 - 24 = GND 25 = THROUGH LINE SUB-D TYPE 25 POLE MALE CONNECTOR CORRESPONDENCE BETWEEN MULTI-POLE SIGNAL AND CONNECTOR 4 SIGNAL 3 GND Attention: No more additions are possible Attention: Only one more I/O module can be added. In order to use the I/O module, the correct right hand endplate with 25 pole female outlet connector must be used. (Code 2240.03.25P). Attention: Signal Not connected GND Connected Through line Connected Please note: this example considers a 37 pinmulti-pole connector. The same configuration managed by a 25 pin multi-pole connector will stop at number 22 of multi-pole connector and at number 17 of themanifold. 22 16 3-4 Module 1 Module 1 Module 2 Not Connected M ulti-pole connector pin 37 poles Connettor 1 3-4 5-6 2 21 5-6 7-8 12 9 10 13 11 14 15 16 3-4 21 5-6 7-8 Module 1 12 9 10 13 11 14 15 16 Module 2 20 17 18 21 19 22 23 24 3-4 21 5-6 9-10 87 18 15 16 19 17 20 21 22 26 23 24 27 25 28 11-1213-14 7-8 10 9 11 12 13 18 17 19 20 21 15 14 16 22 M ulti-pole connector pin 37 poles Connector M ulti-pole connector pi n Maximum 22 Signals 22 Signals : Outlet signals from manifold PIN DESCRIPTION 1 4 3 THROUGH LINE SIGNAL GND